CCL Home Page
Up Directory CCL workers.properties.txt
#
# $Header: /home/cvs/jakarta-tomcat/src/etc/Attic/workers.properties,v 1.3.2.2 2000/10/16 01:59:22 larryi Exp $
# $Revision: 1.3.2.2 $
# $Date: 2000/10/16 01:59:22 $
#
#
# workers.properties -
#
# This file provides jk derived plugins with with the needed information to
# connect to the different tomcat workers.
#
# As a general note, the characters $( and ) are used internally to define
# macros. Do not use them in your own configuration!!!
#
# Whenever you see a set of lines such as:
# x=value
# y=$(x)\something
#
# the final value for y will be value\something
#
# Normaly all you will need to modify is the first properties, i.e.
# workers.tomcat_home, workers.java_home and ps. Most of the configuration
# is derived from these.
#
# When you are done updating workers.tomcat_home, workers.java_home and ps
# you should have 3 workers configured:
#
# - An ajp12 worker that connects to localhost:8007
# - An ajp13 worker that connects to localhost:8009
# - A jni inprocess worker.
# - A load balancer worker
#
# However by default the plugins will only use the ajp12 worker. To have
# the plugins use other workers you should modify the worker.list property.
#
#

#
# workers.tomcat_home should point to the location where you
# installed tomcat. This is where you have your conf, webapps and lib
# directories.
#
workers.tomcat_home=/usr/freeware/jakarta-tomcat/jakarta-tomcat-3.2.

#
# workers.java_home should point to your Java installation. Normally
# you should have a bin and lib directories beneath it.
#
workers.java_home=/usr/java

#
# You should configure your environment slash... ps=\ on NT and / on UNIX
# and maybe something different elsewhere.
#
ps=/
# ps=\

#
#------ ADVANCED MODE ------------------------------------------------
#---------------------------------------------------------------------
#

#
#------ DEFAULT worket list ------------------------------------------
#---------------------------------------------------------------------
#
#
# The workers that your plugins should create and work with
#
worker.list=ajp12, ajp13

#
#------ DEFAULT ajp12 WORKER DEFINITION ------------------------------
#---------------------------------------------------------------------
#

#
# Defining a worker named ajp12 and of type ajp12
# Note that the name and the type do not have to match.
#
worker.ajp12.port=8006
worker.ajp12.host=localhost
worker.ajp12.type=ajp12
#
# Specifies the load balance factor when used with
# a load balancing worker.
# Note:
#  ----> lbfactor must be > 0
#  ----> Low lbfactor means less work done by the worker.
worker.ajp12.lbfactor=1

#
#------ DEFAULT ajp13 WORKER DEFINITION ------------------------------
#---------------------------------------------------------------------
#

#
# Defining a worker named ajp13 and of type ajp13
# Note that the name and the type do not have to match.
#
worker.ajp13.port=8007
worker.ajp13.host=localhost
worker.ajp13.type=ajp13
#
# Specifies the load balance factor when used with
# a load balancing worker.
# Note:
#  ----> lbfactor must be > 0
#  ----> Low lbfactor means less work done by the worker.
worker.ajp13.lbfactor=1

#
# Specify the size of the open connection cache.
#worker.ajp13.cachesize

#
#------ DEFAULT LOAD BALANCER WORKER DEFINITION ----------------------
#---------------------------------------------------------------------
#

#
# The loadbalancer (type lb) workers perform wighted round-robin
# load balancing with sticky sessions.
# Note:
#  ----> If a worker dies, the load balancer will check its state
#        once in a while. Until then all work is redirected to peer
#        workers.
worker.loadbalancer.type=lb
worker.loadbalancer.balanced_workers=ajp12, ajp13


#
#------ DEFAULT JNI WORKER DEFINITION---------------------------------
#---------------------------------------------------------------------
#

#
# Defining a worker named inprocess and of type jni
# Note that the name and the type do not have to match.
#
# worker.inprocess.type=jni

#
#------ CLASSPATH DEFINITION -----------------------------------------
#---------------------------------------------------------------------
#

#
# Additional class path components.
#
# worker.inprocess.class_path=$(workers.tomcat_home)$(ps)classes

#
# The XML parser provided with Tomcat
#
# worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)jaxp.jar
# worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)parser.jar

#
# Tomcat's implementation
#
# worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)jasper.jar
# # worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)servlet.jar
worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)webserver.jar

#
# Javac as available from Java2SE
#
# worker.inprocess.class_path=$(workers.java_home)$(ps)lib$(ps)tools.jar

#
# Setting the command line for tomcat
# Note: The cmd_line string may not contain spaces.
#
# worker.inprocess.cmd_line=-config
# worker.inprocess.cmd_line=$(workers.tomcat_home)/conf/jni_server.xml
# worker.inprocess.cmd_line=-home
# worker.inprocess.cmd_line=$(workers.tomcat_home)

#
# The JVM that we are about to use
#
# This is for Java2
#
# worker.inprocess.jvm_lib=$(workers.java_home)$(ps)jre$(ps)bin$(ps)classic$(ps)jvm.dll

#
# And this is for jdk1.1.X
#
#worker.inprocess.jvm_lib=$(workers.java_home)$(ps)bin$(ps)javai.dll
#

#
# Setting the place for the stdout and stderr of tomcat
#
# worker.inprocess.stdout=$(workers.tomcat_home)$(ps)inprocess.stdout
# worker.inprocess.stderr=$(workers.tomcat_home)$(ps)inprocess.stderr

#
# Setting the tomcat.home Java property
#
# worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home)

#
# Java system properties
#
# worker.inprocess.sysprops=java.compiler=NONE
# worker.inprocess.sysprops=myprop=mypropvalue

#
# Additional path components.
#
# worker.inprocess.ld_path=d:$(ps)SQLLIB$(ps)bin
#


Modified: Wed Apr 18 05:08:07 2001 GMT
Page accessed 4008 times since Tue Feb 4 15:23:34 2003 GMT