# # $Header: /home/cvspublic/jakarta-tomcat/src/etc/workers.properties,v 1.3.2.1 2000/09/04 21:12:30 larryi Exp $ # $Revision: 1.3.2.1 $ # $Date: 2000/09/04 21:12:30 $ # # # workers.properties - # # This file provides jk derived plugins with with the needed information to # connect to the different tomcat workers. # # As a general note, the characters $( and ) are used internally to define # macros. Do not use them in your own configuration!!! # # Whenever you see a set of lines such as: # x=value # y=$(x)\something # # the final value for y will be value\something # # Normaly all you will need to modify is the first properties, i.e. # workers.tomcat_home, workers.java_home and ps. Most of the configuration # is derived from these. # # When you are done updating workers.tomcat_home, workers.java_home and ps # you should have 3 workers configured: # # - An ajp12 worker that connects to localhost:8007 # - An ajp13 worker that connects to localhost:8009 # - A jni inprocess worker. # - A load balancer worker # # However by default the plugins will only use the ajp12 worker. To have # the plugins use other workers you should modify the worker.list property. # # # # workers.tomcat_home should point to the location where you # installed tomcat. This is where you have your conf, webapps and lib # directories. # workers.tomcat_home=usr/local/tomcat_3.2b5/build/tomcat # # workers.java_home should point to your Java installation. Normally # you should have a bin and lib directories beneath it. # workers.java_home=/usr/local/jdk1.3 # # You should configure your environment slash... ps=\ on NT and / on UNIX # and maybe something different elsewhere. # # ps=\ ps=/ # #------ ADVANCED MODE ------------------------------------------------ #--------------------------------------------------------------------- # # #------ DEFAULT worket list ------------------------------------------ #--------------------------------------------------------------------- # # # The workers that your plugins should create and work with # worker.list=ajp12,ajp13 # #------ DEFAULT ajp12 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # # # Defining a worker named ajp12 and of type ajp12 # Note that the name and the type do not have to match. # # #------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # # # Defining a worker named ajp13 and of type ajp13 # Note that the name and the type do not have to match. # worker.ajp12.port=5006 worker.ajp12.host=localhost worker.ajp12.type=ajp12 # # Specifies the load balance factor when used with # a load balancing worker. # Note: # ----> lbfactor must be > 0 # ----> Low lbfactor means less work done by the worker. worker.ajp12.lbfactor=1 worker.ajp13.port=5007 worker.ajp13.host=localhost worker.ajp13.type=ajp13 # # Specifies the load balance factor when used with # a load balancing worker. # Note: # ----> lbfactor must be > 0 # ----> Low lbfactor means less work done by the worker. worker.ajp13.lbfactor=1 # # Specify the size of the open connection cache. #worker.ajp13.cachesize # #------ DEFAULT LOAD BALANCER WORKER DEFINITION ---------------------- #--------------------------------------------------------------------- # # # The loadbalancer (type lb) workers perform wighted round-robin # load balancing with sticky sessions. # Note: # ----> If a worker die the load balancer will check its state # once in a while. Until then all work is redirected to peer # workers. # worker.loadbalancer.type=lb # worker.loadbalancer.balanced_workers=ajp12, ajp13 # #------ DEFAULT JNI WORKER DEFINITION--------------------------------- #--------------------------------------------------------------------- # # # Defining a worker named inprocess and of type jni # Note that the name and the type do not have to match. # # worker.inprocess.type=jni # #------ CLASSPATH DEFINITION ----------------------------------------- #--------------------------------------------------------------------- # # # Additional class path components. # worker.inprocess.class_path=$(workers.tomcat_home)$(ps)classes # # The XML parser provided with Tomcat # worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)jaxp.jar worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)parser.jar # # Tomcat's implementation # # worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)jasper.jar worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)servlet.jar # worker.inprocess.class_path=$(workers.tomcat_home)$(ps)lib$(ps)webserver.jar # # worker.inprocess.stdout=$(workers.tomcat_home)$(ps)inprocess.stdout # worker.inprocess.stderr=$(workers.tomcat_home)$(ps)inprocess.stderr # # Setting the tomcat.home Java property # worker.inprocess.sysprops=tomcat.home=$(workers.tomcat_home)